BOXI is a leading manufacturer of high-quality Auto parts. The company has providing improved technology and outstanding performance solutions for domestic passenger cars, SUVs, trucks. BOXI offers a wide range of revolutionary products. Each product is tested to perform as well as the original units and in many cases to exceed the manufactures specification. About Tire Pressure Monitoring System SensorWhat is TPMS?Tire Pressure Monitoring Sensor monitors tire pressure and temperature. It helps you know the situation of four tires and prompts you to take in-time actions to prevent puncture and damage to car parts caused by flat tires. It also helps prevent flat tires, forecast leakage, reduce tire wire, prolong tire life, improve fuel efficiency and increase traffic safety. Product description Tire Pressure Monitoring Sensor(TPMS) Fits as below vehicles:For Chrysler Models2010-2020 Chrysler 3002011-2016 Chrysler Town & CountryFor Dodge Models 2010-2020 Dodge Challenger2010-2020 Dodge Charger2011-2015 Dodge Durango2011-2020 Dodge Grand Caravan2011-2020 Dodge Journey2012-2016 Dodge C/V2013-2018 Dodge Viper2010 Dodge Ram 15002010 Dodge Ram 2500 For Fiat Models2012-2019 Fiat 5002014-2018 Fiat 500LFor Jeep & Ram Models2011-2015 Jeep Grand Cherokee2013-2019 Jeep Wrangler2011-2013 Ram 15002011-2013 Ram 25002012-2015 Ram C/VInterchange Part Number : 56029398AB, 68142397AA, 68241067AA, 68241067AB, 68406537AA 5S12948 974043 974302 TX-S033RColor: BlackFrequency: 433MHzPlacement on Vehicle: Left, Right, Front, RearPackage :4 x Tire Pressure SensorImportant Notes: 1.This tire pressure sensor has been programmed in advance, no need to reprogram, just trigger it with tpms scan tool. 2.Please DO NOT attempt to start a sensor replacement job if your scan tool or OBD diagnostic tool cannot detect our sensor to display information such as Real ID,Pressure, Frequency, battery statusThe TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition switch to ON/RUN with the engine off. 3. Press and hold the keyless-entry fob transmitter’s LOCK and UNLOCK buttons, at the same time, for about five seconds to start the TPMS learn mode. The horn sounds twice indicating the TPMS receiver is ready and in learn mode. This can also be performed using the turn signal arm and the driver information center. 4. Starting with the left-front tire, activate the sensor by holding the TPMS tool aimed upward against the tire sidewall close to the wheel rim at the valve stem location. Press and release the activate button and wait for a horn chirp. 5. Once the horn chirp has sounded, the sensor information is learned and a turn signal will illuminate in the next location to be learned. On most models, the driver-side-front will be next. Once the learn mode has been enabled, each of the sensors’ unique identification codes can be learned. 6. When a sensor ID has been learned, the module sends a serial data message to the BCM to sound a horn chirp. This verifies the sensor has transmitted its ID and has received and learned it. The module must learn the sensor IDs in the proper sequence to determine each sensor’s location. The first learned ID is assigned to the left-front location, the second to right-front, the third to right-rear and the fourth to left-rear. The TPMS sensor matching process via DIC 1.Set the parking brake.2.Turn the ignition to ON/RUN with the engine off.3.Use the MENU button to select the Vehicle Information menu in the Driver Information Center (DIC).4.Use the thumbwheel to scroll to the Tire Pressure Menu item screen.5.Press the SET/CLR button to begin the sensor matching process. A message requesting acceptance of the process should display.6.Press the SET/CLR button again to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen. 7.Start with the driver side front tire.8.Place the relearn tool against the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.9.Repeat the procedure in Step 8 for RF/RR/LR. The horn sounds two times to indicate the sensor identification code has been matched, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.10.Turn the ignition to LOCK/OFF.